Difference between revisions of "Building a Panel With Recessed Switches"

From OrbiterWiki
Jump to navigation Jump to search
(New page: Here's an example of building a panel like you find in the center console of the Space Shuttle, where the toggle switches are recessed so they won't get kicked by stepping on the panel. Yo...)
 
Line 7: Line 7:
 
Step 3. Transfer the layout to the panel for fabrication
 
Step 3. Transfer the layout to the panel for fabrication
  
Step 4. Make the recesses. Drill Holes in the panel where the recesses are to be, then using a jigsaw, make the recesses the needed rectangular shape. You can also use a sharp chisel to make or clean up the holes.
+
Step 4. Make the recesses. Drill Holes in the panel where the recesses are to be, then using a jigsaw, make the recesses the needed rectangular shape. You can also use a sharp chisel to make or clean up the holes. TODO - post image
  
Step 5. Create the switch guards. Cut some 1/8" steel rod to length, making them about 1/2" longer than the recess. I suggest using a hand saw or cutoff tool rather than a jigsaw, as the jigsaw can bend the rod as it cuts through and its extra work to straighten them again.
+
Step 5. Create the switch guards. Cut some 1/8" steel rod to length, making them about 1/2" longer than the recess. I suggest using a hand saw or cutoff tool rather than a jigsaw, as the jigsaw can bend the rod as it cuts through and its extra work to straighten them again. TODO - post image
  
 
Step 6. Using a small chisel, create holes for the steel rod to fit into so that the top will be flush with the top of the panel.
 
Step 6. Using a small chisel, create holes for the steel rod to fit into so that the top will be flush with the top of the panel.
  
Step 7. Glue the guards to the panel using a multi substrate glue like epoxy or Gorilla (tm) glue.
+
Step 7. Glue the guards to the panel using a multi substrate glue like epoxy or Gorilla (tm) glue. TODO - post image
  
 
Step 8. Sand everything smooth, prime and paint.
 
Step 8. Sand everything smooth, prime and paint.
  
Step 9. Cut out a back plate to mount the switches to, e.g. aluminum. Sand, prime and paint, then mount the switches.
+
Step 9. Cut out a back plate to mount the switches to, e.g. aluminum. Sand, prime and paint, then mount the switches. TODO - post image
  
 
Step 10. Place the switch panel underneath the recess panel, aligning the switches so they are centered. Fasten the back plate to the panel with screws.
 
Step 10. Place the switch panel underneath the recess panel, aligning the switches so they are centered. Fasten the back plate to the panel with screws.
  
Step 11. Add labeling and wiring.
+
Step 11. Add labeling and wiring. TODO - post image

Revision as of 01:36, 20 October 2008

Here's an example of building a panel like you find in the center console of the Space Shuttle, where the toggle switches are recessed so they won't get kicked by stepping on the panel. You'll notice that where multiple switches share a recess, there is a guard wire between each switch.

Step 1. Create your Layout

Step 2. Glue two pieces of MDF together to create a 1" thick panel

Step 3. Transfer the layout to the panel for fabrication

Step 4. Make the recesses. Drill Holes in the panel where the recesses are to be, then using a jigsaw, make the recesses the needed rectangular shape. You can also use a sharp chisel to make or clean up the holes. TODO - post image

Step 5. Create the switch guards. Cut some 1/8" steel rod to length, making them about 1/2" longer than the recess. I suggest using a hand saw or cutoff tool rather than a jigsaw, as the jigsaw can bend the rod as it cuts through and its extra work to straighten them again. TODO - post image

Step 6. Using a small chisel, create holes for the steel rod to fit into so that the top will be flush with the top of the panel.

Step 7. Glue the guards to the panel using a multi substrate glue like epoxy or Gorilla (tm) glue. TODO - post image

Step 8. Sand everything smooth, prime and paint.

Step 9. Cut out a back plate to mount the switches to, e.g. aluminum. Sand, prime and paint, then mount the switches. TODO - post image

Step 10. Place the switch panel underneath the recess panel, aligning the switches so they are centered. Fasten the back plate to the panel with screws.

Step 11. Add labeling and wiring. TODO - post image