Editing Cockpit Layout

Jump to navigation Jump to search

Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.

Latest revision Your text
Line 26: Line 26:
  
 
If you want to build a replica of an [[Orbiter]] spacecraft, a screenshot of a 2D panel is a good start. Expanding a screenshot to full size could get a little fuzzy. A couple solutions to that is convert it to lines from a photo program, or even trace the image and scan that in.
 
If you want to build a replica of an [[Orbiter]] spacecraft, a screenshot of a 2D panel is a good start. Expanding a screenshot to full size could get a little fuzzy. A couple solutions to that is convert it to lines from a photo program, or even trace the image and scan that in.
 
[[ToddWessConstructionDiagrams | Here]] are some dimensional drawings from toddwess of his Shuttle flight deck.
 
  
 
Inexpensive CAD tools:
 
Inexpensive CAD tools:
Line 35: Line 33:
 
Once you have drawings, its time to build a mockup.
 
Once you have drawings, its time to build a mockup.
  
If you've drawn the cockpit from scratch, you probably already have your dimensions set. If you don't, by printing out sections of your drawing at expanded scales you can get a ratio for pulling additional dimensions from your drawings. To do this, expand the printout until a known (or desired) dimension matches a scaled printout of the drawing. As an example, let us say you want to build a Space Shuttle. Flight Deck dimensions are hard to find, but you can find that the original CRT displays were 5"x7". Given that you have a line drawing of the main instrument panel (MIP) of the Space Shuttle, you can expand your drawing until a printout is that dimension. you then have the ratio to convert any dimension on the drawing to full-scale (or less if space is an issue.) Normally you would want a full-scale cockpit(i.e. 100% of the true size), but if space is an issue, anything down to 85% scaling is an adequate substitute and is used by some aircraft flight simulators. Note that using this technique there is a margin of error that increases the smaller the known dimension, so try to find the largest known dimension possible.
+
If you've drawn the cockpit from scratch, you probably already have your dimensions set. If you don't, by printing out sections of your drawing at expanded scales you can get a ratio for pulling additional dimensions from your drawings. To do this, expand the printout until a known (or desired) dimension matches a scaled printout of the drawing. As an example, let us say you want to build a Space Shuttle. Flight Deck dimensions are hard to find, but you can find that the original CRT displays were 5"x7". Given that you have a line drawing of the main instrument panel (MIP) of the Space Shuttle, you can expand your drawing until a printout is that dimension. you then have the ratio to convert any dimension on the drawing to full-scale (or less if space is an issue.) Normally you would want a full-scale cockpit(i.e. 100% of the true size), but if space is an issue, anything down to 85% scaling is an adequate substitute and is used by some aircraft flight simulators. Note that using this technique there is a margin of error that increases the smaller the known dimension, so try to find the largest known dimension possible.
  
Having the life-size dimensions, either your own or scaled from drawings, you can then cut replicas out of cardboard or foam board to get a feel for what you're building and let you adjust positions of things until its the way you want. At this point you can begin adding your controls to portions of your mockup. Normally you would work with individual panels printed to letter-size paper. If you have access to a copy shop or someone with wide format printing capability, it is possible to print, for example, an entire full-scale forward panel at one time. It is generally more cost-effective to print the sections individually.
+
Having the life-size dimensions, either your own or scaled from drawings, you can then cut replicas out of cardboard or foam board to get a feel for what you're building and let you adjust positions of things until its the way you want. At this point you can begin adding your controls to portions of your mockup. Normally you would work with individual panels printed to letter-size paper. If you have access to a copy shop or someone with wide format printing capability it is possible to print, for example, an entire full-scale forward panel at one time. It is generally more cost-effective, though, to print the sections individually.
  
 
By printing individual sets of controls, you can customize your cockpit quite effectively. As an example, You could build a cockpit for one of the Orbiter spacecraft (DG, Dragonfly or Shuttles) and position a Space Shuttle Electrical or Life Support panel in a likely position.
 
By printing individual sets of controls, you can customize your cockpit quite effectively. As an example, You could build a cockpit for one of the Orbiter spacecraft (DG, Dragonfly or Shuttles) and position a Space Shuttle Electrical or Life Support panel in a likely position.
Line 45: Line 43:
 
==Build it==
 
==Build it==
 
[[Flight Deck Materials]]
 
[[Flight Deck Materials]]
 
[[Flight Deck Seats]]
 
  
 
==Cockpit Layout/Display and Control References==
 
==Cockpit Layout/Display and Control References==
Line 53: Line 49:
 
[http://human-factors.arc.nasa.gov/ihi/research_groups/isis/Publications/McCann_Space2005.pdf Automating Vehicle Operations in Next-Generation Spacecraft: Human Factors Issues]
 
[http://human-factors.arc.nasa.gov/ihi/research_groups/isis/Publications/McCann_Space2005.pdf Automating Vehicle Operations in Next-Generation Spacecraft: Human Factors Issues]
  
[[Category: Articles]]
 
 
[[Category:Tutorials]]
 
[[Category:Tutorials]]

Please note that all contributions to OrbiterWiki are considered to be released under the GNU Free Documentation License 1.2 (see OrbiterWiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To protect the wiki against automated edit spam, we kindly ask you to solve the following hCaptcha:

Cancel Editing help (opens in new window)